Tektronix 1740A/1750A Bedienungsanleitung Seite 68
- Seite / 143
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Using the Menus
1740A/1750A Series Waveform/Vector Monitor User Manual
3-13
If it becomes necessary to compensate for minor shifting of
markers due to drift or external magnetic fields (particularly
if the instrument is moved after the markers are set), enter
the
CRT menu and select READOUT. Use the bezel controls to
adjust vertical position
(VPOS) and horizontal position
(HPOS) until the center of the displayed test pattern is at the
center of the graticule.
With Waveform Display
Voltage Cursors can be used to make accurate signal ampli-
tude measurements. With
VOLT selected, use the left bezel
control to position the
VOLT1 cursor at the upper excursion of
signal to be measured, and the center bezel control to posi-
tion the
VOLT2 cursor at the lower excursion. The on-screen
readout gives the voltage difference between the two levels.
When
GAIN is changed, the voltage cursors maintain their
relationship with the signal. For example, if the
VOLT2 cursor
were set to the signal sync tip in
X1 GAIN,itwouldalsobeat
sync tip in
X5 gain, X10 gain, or with VAR gain on.
Timing Cursors can be used to make accurate time measure-
ments. When
TIME is selected, position the TIME1 cursor at
the left excursion of the signal to be measured, and the
TIME2
cursor on the right. The on-screen readout gives the time
difference between the two points.
When
MAG is selected, the timing cursors maintain their rela-
tionship with the signal. For example, if the
VOLT1 cursor
were set to the rising edge of sync, it would also be set there
with
MAG selected.
Markers. When
MARK is selected, use the bezel controls to
vertically position the markers where desired with respect to
the graticule markings. These markers are designed to be
used for reference points; there is no amplitude readout. The
markers are not affected by
GAIN changes; if a marker were
set to
100 IRE in X1 GAIN, it would still be set to 100 IRE with
the
MAG on.
- User Manual 1
- 1740A/1750A Series 1
- Waveform/Vector Monitor 1
- 070-8470-06 1
- General Safety Summary 2
- Safety Terms and Symbols 3
- TABLE OF CONTENTS 5
- Making Measurements 7
- LIST OF FIGURES 9
- Table of Contents 10
- Service Manual 12
- Introduction 14
- Product Description 16
- Features 17
- Description of Features 17
- More Information 18
- Power Cord Options 20
- CRT Options 21
- Accessories 22
- Field Upgrade Kits 23
- Installation 24
- Electrical Installation 25
- Remote Connector 26
- Operational Changes 26
- Mechanical Installation 27
- Rackmounting 28
- Instrument Configuration 29
- Getting Started 30
- AT A GLANCE 31
- Multi- Use Controls 32
- At A Glance 33
- POSITION 35
- Rear-Panel Connectors 38
- AC Power 39
- Fan Filter 39
- Operator’s Checkout 41
- Procedure 41
- Operator’s Checkout Procedure 43
- 10S/DIV 47
- VECTOR PHASE 52
- . This provides the 53
- Operation Basics 55
- Functional Overview 56
- Displaying a Signal 58
- Using the Menus 60
- Clear Menu 61
- Exiting a Menu Function 61
- Cursor Menu 63
- Waveform Cursor Control 64
- T shows the 65
- Using the Cursors 66
- With Waveform Display 68
- Line Select Menu 69
- Preset Menu 71
- Configure Menu 73
- ST ANDARD 75
- CALIBRATE 76
- (Dual Standard Only) 78
- Gain Menu 79
- CRT Menu 79
- Remote Operation 80
- Measurements 81
- Basic Measurements 82
- NTSC Vertical Scales 83
- PAL Vertical Scale 84
- Dual-Standard Vertical Scale 85
- Making Waveform Measurements 86
- Vector Graticule 88
- MakingVectorMeasurements 90
- S C / H R --- Y 93
- Horizontal Sync 94
- Making Audio Measurements 96
- Time Code Display 97
- Calibration 98
- Appendices 100
- Appendix A 101
- Performance Specification 101
- Electrical Specifications 102
- CATEGORY 103
- DESCRIPTION 103
- Table A- 5: RGB/YRGB 107
- Table A- 6: Calibrator 108
- Table A- 7: Vector Mode 108
- Table A- 8: Audio Mode 110
- Table A- 9: Time Code 110
- Table A- 12: Power Source 112
- Appendix B 116
- Remote Connectors 116
- Appendix B: Remote Connectors 117
- Remote Connector Converter 119
- RS232 Connector 120
- Appendix C 121
- User Service 121
- Graticule Light Replacement 122
- Cleaning 124
- Replacing the CRT Filter 125
- Appendix C: User Service 126
- Appendix D 127
- Software Version 127
- Glossary 129
- Y Abbreviation for luminance 138
Verwandte Produkte und Handbücher für Monitore Tektronix 1740A/1750A
Monitore Tektronix MTM400 Bedienungsanleitung
(197 Seiten)
(197 Seiten)
Monitore Tektronix 070-8811-08 Bedienungsanleitung
(121 Seiten)
(121 Seiten)
Foremost KNCA3021D manuals
Owner’s manuals and user’s guides for Unknown Foremost KNCA3021D.
We providing 1 pdf manuals Foremost KNCA3021D for download free by document types: Instruction Manual
Kommentare zu diesen Handbüchern